Tighten the thumbwheel at both ends of the cross-bar. Do not hang any type of accessory or accessory bracket from the plug. Stop the vehicle as soon as safely possible, switch off the engine and let the engine cool. If your vehicle requires professional service, your authorized dealer can provide the necessary parts and service. Loosen each wheel lug nut one-half turn counterclockwise but do not remove them until the wheel is raised off the ground.
Using the right bulbs Replacement bulbs are specified in the chart below. Utility and four-wheel drive vehicles are not designed for cornering at speeds as high as passenger cars any more than low-slung sports cars are designed to perform satisfactorily under off-road conditions. The delay time is set to 20 seconds at the factory, but the delay time may be changed by following the steps below Steps 1 through 6 must be done within 10 seconds : 1. The larger, rearward, compartment is for customer storage. Your vehicle is not a passenger car.
Only use a washer fluid that meets Ford specifications. Slide the cross-bar to the desired location. Reproduction by any means, electronic or mechanical including photocopying, recording or by any information storage and retrieval system or translation in whole or part is not permitted without written authorization from Ford Motor Company. We stand behind our product with a 100% money back guarantee. Ensure that both cross-bar assemblies are installed with the F front arrow facing towards the front of the vehicle. The fact that the airbags did not inflate in a collision does not mean that something is wrong with the system. Canadian customers who require roadside assistance, call 1—800—665—2006.
We know buying anything online is a risk. Check your tire pressure to ensure tires are properly inflated;. If the sliding car icon steadily, have the system service by an authorized dealer immediately. Pull the bulb straight out of the socket and push in the new bulb. After an accident, if the engine cranks but does not start, this switch may have been activated.
To replace the wiper blade: 1. To remove, open the console lid and pull the bin straight up and out from the console housing. Refer to Inflating your tires in the Tires, Wheels and Loading chapter. At the front of the vehicle, lift up on the auxiliary latch handle located in the center between the hood and the grille. Position the jack directly below the stud on the rear trailing arm. Note: Make sure the floor is clear of all objects before folding the seat. Headlamps on warning chi Summary of the content on the page No.
To reset the switch, refer to the Fuel pump shut-off switch in the Roadside Emergencies chapter. Depress the lever and carefully pry the license plate lamp assembly located above the license plate from the liftgate. Turn the handle counterclockwise and lower the spare tire until it can be slid rearward and the cable is slack. Ford is also allowed a final repair attempt in some states. If the beads do not seat at the maximum pressure indicated, re-lubricate and try again. Experience has shown that our customers have been very successful in achieving satisfaction by following the three-step procedure outlined on the front page of the Warranty Guide.
When you are sure that all the pressure has been released, use the cloth to turn it counterclockwise and remove the cap. Removing the jumper cables Remove the jumper cables in the reverse order that they were connected. The high-pressure fluid could penetrate the sealed parts and cause damage. Lift the yellow tab to release the hinges. The safety belt pretensioners activate during frontal collisions, and in side collisions and rollovers.
When your vehicle is not moving, this function shows , one or no bars illuminated. Turn the lumbar support control clockwise to increase firmness. Check with your authorized dealer for availability. Do not be concerned if your engine sometimes knocks lightly. It also may result in unnecessary tire stress, irregular wear, loss of vehicle control and accidents.
The type of fluid used is normally indicated on the dipstick blade and also in the Maintenance product specifications and capacities section in this chapter. To set the parking brake, press the parking brake pedal down until the pedal stops. Squeeze the locking tabs to release the blade from the arm and pull the blade away from the arm to remove it. Rotate to the second position to turn on the headlamps. For more detailed information about towing a trailer, refer to Trailer towing in the Tires, Wheels and Loading chapter. Pull the cushion to the outboard side of the vehicle. These temporary malfunctions can be corrected by filling the fuel tank with good quality fuel, properly tightening the fuel cap or letting the electrical system dry out.