Step 2: Disconnect air compressor fuse. Step 4: Remove wheel Step 5: Disconnect shock sensor connector at the top of shock disconnect air line by turning clip 90 degrees. Locate the air compressor fuse using your vehicle's owner's manual and remove fuse. If upper shock absorber mounting bolts are difficult to remove, you may need to use a floor jack to relieve the pressure on the mounts. Reconnect brake line on differential. There is a clip holding the wire harness to the vehicle. Reconnect sway bar and shock.
Need help finding your suspension solution? Start by disconnecting the brake sensor. Now you can remove the sway bar and spring normally. Rear shocks fill and hold with weigh and doesnt run that much. Keeping your vehicle level helps you to maintain control when you are towing. Save even more money if you convert to our Chevrolet Suburban 1500 conversion kit for a smooth and soft ride. No matter what you suspension needs, Strutmasters has you covered.
The third-row bench is easily accessed courtesy of an available second-row fold-and-tumble feature. Chevrolet Suburban 1500 suspension systems are great but when the Chevrolet Suburban 1500 struts fail or the Chevrolet Suburban 1500 air springs go out, it's almost impossible to drive. Now you can remove the sway bar and spring normally. Next time going to check the sensors. Shock and compressor are all new.
. In light load situations, such as cruising on a flat highway, power is cut from eight to four cylinders in an effort to conserve fuel. Remove this clip so that the wiring harness can be easily accessed. Interior materials are acceptable, if not high-end, and the overall appearance is stylish yet understated. Installation of a Z55 suspension conversion kit should only be undertaken by an experienced and qualified mechanic.
No information contained in this video shall create any expressed or implied warranty or guarantee of any particular result. I decided to buy with them, and was able to drive away with the car in just over an hour of being there. Full instructions on installing Electronic Bypass Module is included with the conversion kit This guide is based on information provided by Arnott and is not intended to give a complete explanation of all steps required. Step 1: Disconnect battery - this prevents the possibility of an electrical short. Storage is plentiful, with generous armrest storage and multiple pockets and cupholders.
Asking for some assistance in which direction i should start to look in. I'm going to lift the truck today and check the front for air leaks. Strutmasters conversion kits are designed to bolt directly onto your vehicle without drilling or other modifications. When it comes to vehicles you can buy off your local dealer's lot, there's not much capable of casting a shadow over the 2011 Chevrolet Suburban. © Copyright 2019 Designed by: Developed by:.
There is a clip holding the wire harness to the vehicle. Locate the air compressor fuse using your vehicle's owner's manual and remove fuse. Make sure that you install the spring in the correct orientation. If upper shock absorber mounting bolts are difficult to remove, you may need to use a floor jack to relieve the pressure on the mounts. Shop by Make and Model Here at Strutmasters we understand that our customers want to know what is going on with their vehicle and understand what they are buying. Especially well-suited for large families and those who tow a camper, boat or horse trailer, the 2011 Chevrolet Suburban is a completely modernized version of a genuine workhorse.
Remove this clip so that the wiring harness can be easily accessed. It is the sole responsibility of the viewer to assume this risk. Step 4: Remove wheel Step 5: Disconnect shock sensor connector at the top of shock disconnect air line by turning clip 90 degrees. Power-Operated Running Boards The available power-operated running boards, which pop out when a door is opened and retreat when closed, are of considerable help for passengers who find getting into and out of the Suburban to be difficult. Inside its cavernous confines is seating for up to nine occupants, cargo space that maxes out at 137.
Installation of a Z55 suspension conversion kit should only be undertaken by an experienced and qualified mechanic. I just replaced one front impact sensor and two months later the other side goes bad. For a more aggressive look and added capability, the Z71 Off-Road Package fits the Suburban with off-road tires and suspension components, skid plates, an automatic locking rear differential and a chrome grille. Reconnect ride height sensor and brake sensor. Give Strutmasters a call at 866-597-2397 today. That third row is, however, a bit old school in that it cannot be completely folded into the floor; it must be removed if you wish to maximize cargo space.
Unbolt ride height sensor and be careful not to damage it. Great truck but all these little annoyances are starting to get tired some. Removal of a coil spring is potentially very dangerous. I installed new rear shocks and i still get the service suspension display. That's the case with the truck I purchased from them that had a few surprises in store.